CML

CML

CML is een Italiaans bedrijf uit Gessate, Milaan dat sinds 1960 meervoudzagen produceert. Wereldwijd zijn er meer dan 5000 bedrijven die elke dag met CML machines werken, en dit is het resultaat van meer dan 60 jaar ervaring.
Categories: , ,
CML_275x0

Technical Specifications

Quality and innovation are the hallmarks of the brand. CML's production programme consists of more than 30 different models. The maximum cutting width ranges from 220 to approx. 1300 mm. The maximum cutting thickness ranges from 80 to 270 mm.

The motor power ranges from 20 HP for the E 350 model up to 2x 180 HP for a lower and upper saw shaft on the SCA 500  B/O model.

CML Engineering also creates total solutions where the wood is first cut to length and fed automatically to the sawing machine. Discharge and automatic stacking systems are also part of their production programme.

Some models in the  CML range are unique. The Milanese multi-blade saw manufacturer is the only one making machines with a double saw shaft.

In the CML production halls you can see that the entire machine is produced in-house. Both the heavy machine frames and the saw shafts, feed chains and electrical control cabinets are made in-house.

 

At our headquarters we look together at the most suitable machine configuration.

The most important factors are: the maximum thickness of the wood to be cut, the maximum width of the workpiece, the number of cuts that must be made in one pass, the type of wood, the moisture content of the wood, the volume you need to be able to cut per hour, the variation in the cutting pattern and the automation.

 

The basic principles of a multi-blade saw are as follows: 1 HP of power is required to cut dry and hard wood per cm of thickness at a feed speed of approx. 10 metres per minute.

When the wood is still wet, it is best to allow 1.5 HP per centimetre of wood thickness per saw.

 

Example: if we have a piece of oak with a thickness of 100 mm and 5 saws are used, we need a motor of 50 HP for dry wood and 75 HP for wet wood at a feed speed of 10 metres per minute.

If greater production of, for example, 15 metres per minute is required, the motor will need approx. 75 HP for dry oak and 100 HP for wet oak.

 

CML multi-blade saws come in 2 groups:

  • Machines fitted with a long saw shaft with rings. On the Multirip models you can place several saws next to each other on one shaft. By selecting the intermediate rings you can choose the distance between the various saw blades yourself and thus set up the desired cutting pattern. These machines have a fixed shaft.
  • Machines fitted with 1 fixed reference saw on the right-hand side and up to 4 additional mobile saws that can be set according to different criteria via the computer or the control panel. These are the EGGER models (with an R in the type designation), machines with mobile saws that are very flexible since the cutting pattern can be specifically adjusted for each board. All EGGER machines can also be fitted with a fixed saw shaft and work as a multi-rip. This can also be combined with several fixed saws and 1 or more mobile saws. The mobile sawing units can also be fitted with 2 saw blades (1 to the left and 1 to the right of the mobile unit).

Feed chain of CML multi-blade saws:

In traditional multi-rip saws, the sliding feed tracks cause a lot of friction between the guides and the chain. This type of rail causes excessive friction due to the pressure on the working blades. That is why the traditional multi-blade saw needs to be well lubricated to reduce friction and wear. During sawing, the blades produce a lot of sawdust, most of which is removed by the dust extractor, but small amounts remain in the machine.

The sawdust and wood chips fall onto the track, are discharged and exit the machine, but a small amount falls onto the guides of the chain track. Even if the guides are well protected, they become covered with sawdust, which slows down and stops the feed track.

 

CML's system has eliminated these inconveniences thanks to hardened steel guides over which the chain runs without sliding.

The chains run on tempered steel guides, which makes high working loads possible and eliminates the sawdust problem that would normally stop operation.

 

Our system makes it possible to replace only damaged parts instead of the entire belt, as is the case with traditional machines when the steel pads are damaged.

 

Pressure rollers on CML multi-blade saws:

On traditional multi-blade saws the number of upper pressure rollers is at most 4, and they are always parallel to the advancing belt.

 

CML has 3 +  4 pressure rollers on the economy machines, and 10 pressure rollers on the high-level models.

The CML system is innovative because all rollers are mounted on the same group frame, but each roller presses the belt independently and adapts to the differences in the belt (helical and/or bowed), allowing consistent pressure across the entire width of the belt.

 

On the traditional system, in these conditions the rollers only press the wood on the higher part and not the lower part, especially when the wood is not the same height. As a result, each roller gives a different direction of advance, which causes two problems:

  1. During sawing the saw blades are subjected to excessive lateral forces that cause overheating and failure.
  2. From the moment the board is fed into the saws, the board is advanced irregularly and produces cuts that do not correspond to the entry laser.

What makes this machine unique?

%title%

%unique_points_description%

All product images

Ready to

Take the next step?

Request a quote



















Our top 3 machines in this sector

More than just machines: a full-service solution

Buying or renting a machine is one thing. What comes next is what makes the difference.
At Rogiers, you’re never on your own. From installation to long-term maintenance, our service team ensures that your production keeps running—without any surprises.

Found the right machine for you?

Now is the time to take the next step. Whether you have questions, want to schedule a
demo, or would like a quote right away, we’re here to help.